IBM 60 User Manual Download

Page: 43 / 166

Chapter 4. Customizing the Printer

This chapter gives you step-by-step instructions for customizing your printer to
match your particular printing environment and requirements.

You can use the operator panel to change the printer settings and therefore
customize the way the printer operates. Changing the settings is called configuring.

This chapter provides instructions for:

Configuring the trays

Configuring the stackers

Configuring the printer

Running internal test prints

Configuring attachments

Adjusting the print

Using the default font

Defining form names

Configuring the Trays

Both key operators and users can configure certain items relating to the trays. The
user can do the following:

Change the form size and form name loaded in each tray

Select an autoswitch tray

The key operator also can do the following:

Enable and disable trays

Note: Always adjust the size guides in the tray for the correct paper size before
configuring that tray. Refer to “Loading Paper” on page 5-9.

Tray Names

The following artwork shows a model with all possible trays. Your printer may not
have the optional side tray installed.

Note: Paper input receptacles are referred to as

trays. Paper output receptacles

are referred to as

stackers.



4-1

Summary of Contents for 60







































































































































































Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands

IBM 60, User Manual

Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands