![HUSABERG FE 450 AUS Repair Manual Download Page 183](http://html1.mh-extra.com/html/husaberg/fe-450-aus/fe-450-aus_repair-manual_2187561183.webp)
FAULT CODE
181
Flash code FI warning
lamp (MIL)
12
FI
warning lamp (
MIL
) flashes 1x long, 2x short
Display on diagnostic tool
P0118
"Coolant temperature sensor"
"Input signal too high"
Error level condition
Coolant temperature sensor cylinder 1 voltage
"TWAD"
:
≥
4.785 V
Time:
≥
3 s
Function check
Coolant temperature sensor cylinder 1 - checking the voltage (
Possible cause
Coolant temperature sensor - value not plausible (
Coolant temperature sensor - signal line has a short circuit to plus (terminal 30) (
Coolant temperature sensor - signal line has a short circuit to ignition plus (terminal 15)
Coolant temperature sensor - signal line has a short circuit to the sensor power supply (
Coolant temperature sensor - signal line is open (
Coolant temperature sensor - ground line is open (
Coolant temperature sensor cylinder 1 - checking the voltage
Condition
The diagnostic tool is connected and active.
–
Select the model type.
–
Select
"ECU Diagnostic"
.
–
Highlight the
"Engine electronics EXC"
control unit.
–
Press
"Continue"
.
–
Select
"Measurement values"
.
–
Highlight
"Mixture preparation, general"
.
–
Press
"Continue"
.
–
Highlight the measured value
"Coolant temperature sensor cylinder 1 voltage (TWAD)"
and deselect the other parameters with
"Select
measured value"
.
Coolant temperature sensor cylinder 1 voltage
"TWAD"
0.138… 4.784 V
» If the displayed value is equal to the setpoint value:
–
Delete the fault code.
–
Make a test ride.
–
Read out the fault code.
» If the displayed value is above the setpoint value:
–
Check the next possible cause:
Coolant temperature sensor - value not plausible (
Coolant temperature sensor - value not plausible
Condition
Th e diagnostic tool is disconnected.
Coolant temperature sensor is disconnected.
400599-10
Coolant temperature sensor - check the resistance
–
Measure the resistance between the specified points.
Coolant temperature sensor Pin
1
–
Coolant temperature sensor Pin
2
Coolant temperature sensor
Resistance at:
−
30 °C (
−
22 °F)
22.86… 27.94 k
Ω
Resistance at:
−
20 °C (
−
4 °F)
13.50… 16.50 k
Ω
Resistance at:
−
10 °C (14 °F)
8.24… 10.08 k
Ω
Resistance at: 0 °C (32 °F)
5.17… 6.31 k
Ω
Resistance at: 10 °C (50 °F)
3.33… 4.07 k
Ω
Resistance at: 20 °C (68 °F)
2.21… 2.70 k
Ω
Resistance at: 30 °C (86 °F)
1.49… 1.83 k
Ω
Resistance at: 40 °C (104 °F)
1.04… 1.27 k
Ω
Resistance at: 50 °C (122 °F)
730… 892
Ω
Summary of Contents for FE 450 AUS
