manualshive.com logo in svg

Goldacres Super Cruiser G8, Operator'S Manual, Page: 23 / 210

Share
Download
Goldacres Super Cruiser G8 Operator'S Manual Download Page 23

Chapter 4 - Cabin -

 19

G8 Super Cruiser Operator’s Manual MY19 - REV 0

Operator Seat

NO.

FEATURE

INSTRUCTIONS

1.

Fore / Aft Adjustment

By lifting this lever the seat can be slid backwards or forward to the 

desired position.

2.

Fore / Aft Locking lever

Release this lever to enable the Fore & Aft adjustment of the seat, and 

engage to lock the seat to the desired position.

3.

Seat Depth Adjustment

To adjust the depth of the seat cushion, pull the handle upwards. By 

moving the seat cushion backwards the desired seating position can be 
reached.

4.

Seat Pan Angle 
Adjustment

To adjust the angle of the seat pan, pull the handle upwards. By exerting 

pressure on or off the front or rear part of the seat pan it can be 
moved to the desired position.

5.

Height Adjustment

By lifting this lever air will be pumped in to the airbag suspension. By 

lowering this lever air is exhausted from the air bag.

6.

Tilt 

The lever on the right hand side of the seat allows the back rest to be 

tilted forward or rearward. Pulling the lever forward releases the back 

rest so it can be repositioned.

7.

Arm Rest Adjust

By turning this knob the arm rest can be lowered or raised to suit.

8.

Lumbar 

By turning this handle the lumbar in the back of the seat will increase or 

decrease the pressure on the operators back.

9.

Seat Belt

Operator lap seat belt must be fitted when ever the operator is seated 

in the cabin.

1

5

3

4

2

6

7

8

9

Summary of Contents for Super Cruiser G8



















































































































































































































Reviews:

No comments