Goldacres Super Cruiser G8, Operator'S Manual, Page: 116 / 210

112 - Chapter 9 - Boom G8 Super Cruiser Operator’s Manual MY19 - REV 0
50 mm measurement at tip,
forward of inner boom.
Clevis lock nut
Run a string line along the back face of lower rear chord on the
inner wing. Extend it out to the boom tip and measure as required.
1. When adjustment of the inner booms is complete
the outer booms can now be aligned.
2. Ensure the fold hinge breakaway spring tension
has been set so there is a 2 mm gap between the
coils.
3. TriTech booms 36-42 m must be 50 mm forward
of the inner booms. Use a string line to assist with
achieving the correct measurements.
4. To adjust the outer boom to get them 50 mm
forward, wind in or out the top boom stopper
bolt.
5. Loosen the locking nut behind the fold cylinder
clevis. Screw the cylinder rod out until the boom
stopper bolt is up hard against the inner boom
and the outer boom so it will not flop around.
6. Set the bottom stopper bolt to sit against the
boom hinge. If this is not done, excessive twisting
load will be exerted on the hinge.
7. Once the position is correct, tighten the lock nut
on the stopper bolts and the nut on the hydraulic
cylinder clevis.
NOTE: It is advised that all threads are lubricated
prior to making adjustments.
NOTE: It is important that both wings are adjusted
the same. If one wing is adjusted further forward or
back than the other, the boom may not sit level.
Alignment - Unfolded Angle - Outer
Boom Adjustment - 36-42 m
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
A3
SHEET 14 OF 14
SCALE:1:7
DWG NO.
TITLE:
GOLDACRES
DO NOT SCALE DRAWING
Material
:
Drawn By:
1-3 MORANG CR
MITCHELL PARK 3352
PH: 03 53426399
FAX: 03 53426308
42m RH Boom Wing
Title
Name
NealHarvey
REV NO CHANGE NAME/DATE ECN NO.
Material <not specified>
DATE EDITED:
2/04/2015
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE
IN MILLIMETRES
UNTOL. DIMENSIONS
OPEN DIM ± 1.00
ANGULAR ± 0.50°
UNLESS OTHERWISE
TOLERANCED
THIS DRAWING REMAINS THE PROPERTY
OF GOLDACRES TRADING PTY LTD AND IS
SUBJECT OF COPYRIGHT
Surface Finish:
Approved
FINISHED WEIGHT: 787.90 Kg
Drawing Checked:
25/05/2017
REV
DRG. STANDARD
/PRACTICE
AS 1100
DEBUR ALL EDGES
00
-
- -
- -
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
A3
SHEET 14 OF 14
SCALE:1:7
DWG NO.
TITLE:
GOLDACRES
DO NOT SCALE DRAWING
Material
:
Drawn By:
1-3 MORANG CR
MITCHELL PARK 3352
PH: 03 53426399
FAX: 03 53426308
42m RH Boom Wing
Title
Name
NealHarvey
REV NO CHANGE NAME/DATE ECN NO.
Material <not specified>
DATE EDITED:
2/04/2015
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE
IN MILLIMETRES
UNTOL. DIMENSIONS
OPEN DIM ± 1.00
ANGULAR ± 0.50°
UNLESS OTHERWISE
TOLERANCED
THIS DRAWING REMAINS THE PROPERTY
OF GOLDACRES TRADING PTY LTD AND IS
SUBJECT OF COPYRIGHT
Surface Finish:
Approved
FINISHED WEIGHT:
787.90 Kg
Drawing Checked:
25/05/2017
REV
DRG. STANDARD
/PRACTICE
AS 1100
DEBUR ALL EDGES
00
-
- -
- -
Wind stopper bolt in to adjust
boom forward. Wind stopper
bolt out to adjust boom
backward.