![background image](http://html1.mh-extra.com/html/gmc/c-series-1993/c-series-1993_repair-manual_2235927080.webp)
POWER STEERING COMPONENTS
f RW ROSS 3B3-7
• Reverse the assembly in the vise so that the worm
end is down. Use an inch pound torque wrench on
the input shaft, note the torque required to rotate
the input shaft 360 degrees in each direction (fig
ure 9). Tighten the bearing adjuster to increase the
maximum torque at the input shaft 0.56 to 1.13
N-m (5 to 10 in. lbs.).
• Rotate the assembly in the vise.
11. New jam nut (18) with the radius side down.
Tighten
• Jam nut to 154 N-m (112 ft. lbs.) using J 37070
and J 37464 (figure 10).
• Recheck the input shaft torque and repeat above
procedure as necessary. Stake the valve housing
into the clockwise most corner of the two opposing
slots in the jam nut. Stake the jam nut into the
adjuster in one place at threaded area using a suit-,
able punch. Choose areas that have not been pre
viously staked.
Figure 9—Checking Input Shaft Torque
Figure 10—Tightening the Jam Nut
• Torque required to rotate the input shaft must be
between 0.56 to 1/T3 N m (5 to 10 in. lbs.) rnore
that the original torque that was noted.
•T h e torque.required to rotate the input shaft must
not be more than 2.5 N-m (22 in. lbs.). Unstake
. and adjust as necessary.
STEERING GEAR
-►+
Install or Connect (Figures 1 and 2
)
NOTICE: For steps 16, 18, 21, and 32, see
"Notice" on page 3B5-1.
-.-j
Tools Required:
J 37071 Bearing and Seal Tool
, V
J 36452 Poppet Seat Tool,
,, i:
J 37073 Input Seal Installer
1. Retaining ring (34) if re moved, into the g roove clos
est to the side cover end of the bearing bore.
2. Roller bearing (35) if removed, from! the trunnion
end of the bearing bore pressing bearing installa
tion end of J 37071 against the lettered end of the
bearing shell until the bearing is seated against the
retaining ring.
,
i
,
^
• Lubricate the bearing bore. , -
I
• Make sure that the housing is square with the
press base and that the bearing is not cocked.
3. Washer (38) into the side cover side of the housing
seal bore with the small diameter piloted into the
retaining ring (34).
i
j ' ;
y
4. New seal (39) onto J 37071 so the lip with the
spring is toward the. shoulder of the tool.
5. J 37071 into the washer (38) and bearing (35) with
a force of 46 to 362 kg (100 to 800
seal is seated against the washer.
6. New seal (36) with the seal lip out.
7. Retaining ring (34);
/
lbs.) until the
• Pack the area between the seal ’ (36)] and the out
put shaft . seal (39) with clean high temperature
industrial grease.
j
8. New lightly oiled valve housing seals (6 and 7) in
the mounting face grooves.
9. Poppet assemblies (22) if removed.
• Make sure that the. two threaded;poppet holes
in the rack piston and the poppet
j
adjuster seat
and sleeve assemblies are free of thread seal
ing compound. ■, . y y
y - ' ' ]
• Reset the automatic poppet adjuster, seat and
. sleeve assembly (not required for new service
replacement parts) if it was removed by revers
ing it and screwing it loosely into the piston to
its full thread length (slotted end in). Press the
adjuster seat into the adjuster sleeve with a
force of 227 to 1134 kg (500 to 2500 lbs.) until
the shoulder bn the adjuster seat bottoms
against the adjuster sleeve (figure 11 j. Remove
the adjuster seat and sleeve assembly from the
Summary of Contents for C Series 1993
