![background image](http://html1.mh-extra.com/html/gmc/c-series-1993/c-series-1993_repair-manual_2235927097.webp)
5A-4 MASTER CYLINDER
21. Compensating valve spring (6).
7
22. Compensating valve poppets (5).
23. Compensating valve seals (4).
24. O-ring seal (29).
y '
• The primary piston must be depressed in order
to seat the poppet valves while installing the
reservoir.
; , y -.
25. Reservoir (3).
NOTICE: See “ Notice ” on page
5Ar 1.
26. Four bolts (26).
T i g h t e n
. ' • Bolts (26) to 22 N m (16 ft. lbs.).
27. Fill the reservoir; with clean brake fluid.
, 28. Bleed the master cylinder. Refer to “Bench Bleed-
29. Diaphragms (2) and caps (1).
BENCH BLEEDING
The purpose of bench bleeding is .to.-remove.-as much
air as possible from the master cylinder before installing:
it on the vehicle. This reduces the amount of time need
ed for brake system bleeding after the master cylinder
is installed; pn the vehicle. If tools are not available for
bench bleeding, bleed the master cylinder on the vehi
cle fird.j|j;:;!;|::
. y
1; Plugtthp outlet ports and mount the master cylinder
,: in; a| >|/ise: with the front end tilted slightly down.
2. Fiij tlie reservoir with clean brake fluid.
3. Usd;; jap smooth, round-end tool and stroke the pri-
,
maryj piston about 25 mm (1 inch) several times.
•I^Astdir is bled from the master cylinder, resis-
^aripe to primary; piston travel will not allow the
; full 25-mm (1-inch) stroke. ;
y
4.
Reposition the master cylinder in the vise with the
front1
end tilted slightly up.
5. Again ! stroke the primary piston approximately 25
m m ’(1 inch) several times.
6. Reposition the master cylinder ih the vise to a level
pdsitiprV
’ / : \ - y " - ;
":" y '
.'■? '.
7. Loosen the plugs one at a time and push the pis
ton into bore to force air from the cylinder.
8. Close the plugs.
-
9. Fill the reservoir and install the diaphragms (2) and
y
caps (1).
Normal bleeding procedures still need to be done
after the master cylinder
vehicle.
has been installed on the
SPECIFICATIONS
Reservoir Bolts.
FASTENER TIGHTENING SPECIFICATIONS
N m
F t . L b s .
.
............. . . :
. . J
. . ......... .•
22
16
lii. Lbs.
T3025
1
l-
Summary of Contents for C Series 1993
