![background image](http://html1.mh-extra.com/html/gmc/c-series-1993/c-series-1993_repair-manual_2235927026.webp)
1P2-6 HR6-HE AIR CONDITIONING COMPRESSOR
Install or Connect
l .
Place the pulley rotor on the J 2 1352-A support block 't<p
fully support the rotor hub during bearing installation
(F ig - l 0 ) - ,
. .
' j ' K j j j ; '
NOTICE:
DO NOT support the rotor by resting .tHe
pulley rim on a flat surface during the bearing
installation or the rotor face will be bent.
, ;; j || j
2.
Align the new bearing squarely with the hub boreland
using puller and bearing; installer J 9481-A jjw,ith
universal handle ) 29886,;drive the bearing fully into;{he
hub (Fig. 10). The installer will apply forcfe to the outer
race of the bearing, if used as shown.
J !,! ! j
3.
Place bearing staking guide J 33019 - 1 and bearing
staking pin J 33019-2 in the hub bore as shbvyn; in
Figure ll. Shift the rotor and bearing assembly on thjd
J 2 1352-A support block to give full support of the:hub
under the staking pin location! A heavy-duty rubber
band may be used to hold the stake pin in the guide: ( Figi
ll), and the stake pin should be properly positioned iri
the guide after each impact on the pin.
;
J
4.
Using care to prevent personal injury, strike the staking
pin with a hammer until a metal stake, similar tb the
original, is formed
down to
but
not tbuching
thb
bearing.
: Noisy bearing operation and reduced bearing life rriay
1 result if outer bearing race is deformed while staking*
The stake metal should not contact the outer race Of the
. i
i \ ,j-
bearing. Stake three places 120 degrees apart as shown in
Figure 12.
|T 1 J 33019 1 BEARING STAKING GUIDE
m R
ubber
band
i n U 33019-2 BEARING STAKING PIN
L~ ~j . j- |i
l, ;______ - . •
' ■
'
■
_________ G60150-1D2-EK-R1
. '
i ,l
;
'
'
-'
.
• - */
Staking Bearing In Rotor Hub Bore
5. . With the cbmpresSor mounted to the J 33026 holding
fixture, position the rotor, and bearing assembly on the
front head (Fig. 13)..
6.
Position the J 33017 pulley, rotor and bearing installer
gnd J 33023-A puller pilot directly over the inner race of
the bearing (Fig. 13).
7.
Position puller: crossbar J 8433-1 on the puller pilot
J i;3!023-A and assemble the two J 33026-2 through bolts
arid'washers through the puller bar Slots and thread them
into the J 33026 holding fixture (Fig. 13). The thread of
the;thrbugh bolts should engage the full thickness of the
holding fixture.
. •
•
-
.
, ,
•
8.
Tighten the center screw in the J 8433-1 puller crossbar
to Ifpj'ce the pulley rotor and bearing assembly onto the
••^ohJjjressOr,,. front
head
(Fig.
13).
Should the
' Jr3jj01f7; pulley rotor and bearing installer slip off direct
injline contact, with the inner race of the bearing, loosen
:th|e|;J:; 843341 center forcing screw and realign the
installer and pilot so that the J 33017 installer will
properly clear the front head.
r[|i*N H .-'
.
■;
;
9.
Install-rotor and bearing assembly retainer ring, using
.. snap ring pliers J 6083 (Fig. 6).
10. Reinstall clutch plate and hub assembly as described
previously.
Summary of Contents for C Series 1993
