manualshive.com logo in svg

GE L90, Instruction Manual

The GE L90 is a high-performance electrical relay, designed to protect and control electrical power systems. Ensure proper installation and operation with the comprehensive, easy-to-follow Instruction Manual available for free download on our website. Access the manual today at manualshive.com and optimize your power system management effortlessly.

Share
Download
background image

CHAPTER 5: SETTINGS

CONTROL ELEMENTS

L90 LINE CURRENT DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

5-387

5

Set this delay long enough to cope with transient conditions including not only current reversals but also spurious negative 
and zero-sequence currents occurring during breaker operations (in the case when neutral directional overcurrent or 
negative-sequence directional overcurrent functions are used). Consider the breaker failure time of the surrounding 
protection systems within the reach of the ground directional function used by the hybrid POTT scheme, to make sure that 
the ground directional function is not jeopardized during delayed breaker operations.

ECHO DURATION

 — This setting defines the guaranteed and exact duration of the echo pulse. The duration is not dependent 

on the duration and shape of received RX signals. This setting enables the relay to avoid a permanent lock-up of the 
transmit/receive loop.

ECHO LOCKOUT

 — This setting defines the lockout period for the echo logic after sending the echo pulse. This enables the 

relay to avoid oscillations of the echo pulses during an autoreclosure dead-time after clearing an internal fault.

HYB POTT SEAL-IN DELAY

 — The output FlexLogic operand (

HYB POTT OP

) is produced according to the hybrid POTT scheme 

logic. The 

HYB POTT SEAL-IN DELAY

 defines a minimum guaranteed duration of the 

HYB POTT OP

 pulse. As this operand runs 

the trip table of the hybrid POTT scheme, the trip operands 

HYB POTT TRIP A

, 

B

, 

C

, and 

3P

 are sealed-in for the same period of 

time.

GND DIR O/C FWD

 — This setting defines the FlexLogic operand (if any) of a protection element that is used in addition to 

zone 2 for identifying faults on the protected line, and thus, for keying the communication channel and initiating operation 
of the scheme (both through the transient blocking logic). Good directional integrity is the key requirement for an over-
reaching forward-looking protection element used as 

GND DIR O/C FWD

.

Even though any FlexLogic operand could be used as 

GND DIR O/C FWD

 enabling the user to combine responses of various 

protection elements or to apply extra conditions through FlexLogic equations, this extra signal is primarily meant to be the 
output operand from either the negative-sequence directional or neutral directional overcurrent elements. Both these 
elements have separate forward (

FWD

) and reverse (

REV

) output operands. The forward indication should be used (

NEG SEQ 

DIR OC1 FWD

 or 

NEUTRAL DIR OC1 FWD

).

Coordinate the selected protection element (or elements in combination) with the selection of 

GND DIR O/C REV

. For all the 

forward external faults seen by an element used as 

GND DIR O/C FWD

 at one end of the line, the reverse-looking element 

used as 

GND DIR O/C REV

 at the other end picks up and provides a blocking signal. For greater security and to overcome 

spurious directional element operation during transients, adding at least 0.5 cycles of pickup delay to the forward 
directional element is recommended.

GND DIR O/C REV

 — This setting defines the FlexLogic operand (if any) of a protection element used in addition to zone 4 for 

identifying reverse faults, and thus, for stopping the transmit signal and initiating the transient blocking timer. Good 
directional integrity is the key requirement for a reverse-looking protection element used as 

GND DIR O/C REV

.

Even though any FlexLogic operand can be used as 

GND DIR O/C REV

 enabling the user to combine responses of various 

protection elements or to apply extra conditions through FlexLogic equations, this extra signal is primarily meant to be the 
output operand from either the negative sequence directional or neutral directional overcurrent element. Both these 
elements have separate forward (

FWD

) and reverse (

REV

) output operands. Use the reverse indication (

NEG SEQ DIR OC1 REV

 

or 

NEUTRAL DIR OC1 REV

).

Coordinate the selected protection element (or elements in combination) with the selection of 

GND DIR O/C FWD

. For all the 

forward external faults seen by an element used as 

GND DIR O/C FWD

 at one end of the line, the reverse-looking element 

used as 

GND DIR O/C REV

 at the other end picks up and provides a blocking signal. For greater security and to overcome 

spurious directional element operation during transients, adding a pickup delay greater than the pilot channel delay to the 
reverse directional element is recommended.

HYB POTT NO OF COMM BITS

 — This setting specifies the number of bits of the communications channel available for the 

scheme. The transmit codes and trip table of the hybrid POTT scheme are the same as those for the permissive under-
reaching transfer trip scheme. See the description of the PUTT scheme for information.

HYB POTT RX1

 through 

HYB POTT RX4

 — These settings allow the user to select the FlexLogic operands that represent the 

receive signals for the scheme. Typically, input contacts interfacing with a signaling system are used. In single-bit 
applications, 

HYB POTT RX1

 must be used. In two-bit applications, 

HYB POTT RX1

 and 

HYB POTT RX2

 must be used. In four-bit 

applications, 

HYB POTT RX1

, 

HYB POTT RX2

, 

HYB POTT RX3

, and 

HYB POTT RX4

 must be used.

Summary of Contents for L90





































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for L90

1Control Solo Technical Sheet preview
Solo
Brand: 1Control Pages: 8
Dantherm DRC1 Instructions Manual preview
DRC1
Brand: Dantherm Pages: 96
Danfoss 103E7 Installation & User'S Instructions preview
103E7
Brand: Danfoss Pages: 24
QUAD 34 Instruction Book preview
34
Brand: QUAD Pages: 17
fadini VIGILO 2250 Instruction Manual preview
VIGILO 2250
Brand: fadini Pages: 16
L-Acoustics LA8 Product Information preview
LA8
Brand: L-Acoustics Pages: 20
Ultraflex B47 Installation Instructions Manual preview
B47
Brand: Ultraflex Pages: 7
Magicfx FX-COMM4NDER MFX3203 User And Installation Manual preview
FX-COMM4NDER MFX3203
Brand: Magicfx Pages: 16
Game ready Equine 550250 User Manual preview
Equine 550250
Brand: Game ready Pages: 24
EMS ZITON RADIO LOOP MODULE Programming Manual preview
ZITON RADIO LOOP MODULE
Brand: EMS Pages: 26
Danfoss 084B8012 Instructions Manual preview
084B8012
Brand: Danfoss Pages: 30
IR-Tec OS-NET Programming Manual preview
OS-NET
Brand: IR-Tec Pages: 14
Parker PSST8M23A Installation & Service Instructions Manual preview
PSST8M23A
Brand: Parker Pages: 8
Global Fire Equipment Junior V4 Operation & Maintenance Manual preview
Junior V4
Brand: Global Fire Equipment Pages: 23
HOMIDO BTGPIOS-1 Instruction Manual preview
BTGPIOS-1
Brand: HOMIDO Pages: 29
KSB Monosub R Manual preview
Monosub R
Brand: KSB Pages: 16
Thrustmaster 4169089 User Manual preview
4169089
Brand: Thrustmaster Pages: 9
Automated Logic UNI/32 Technical Instructions preview
UNI/32
Brand: Automated Logic Pages: 10

Brands by name

Popular brands

Load more brands