GE L90 Instruction Manual Download Page 613 | Manualshive

Page: 613 / 900

background image

CHAPTER 5: SETTINGS

CONTROL ELEMENTS

L90 LINE CURRENT DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL

5-389

5

Generally, the scheme compares the direction to a fault at all terminals of the line. Unlike the permissive schemes, the
absence of a blocking signal permits operation of the scheme. Consequently, the scheme is biased toward dependability
and requires an "on/off" type of signaling.
By default, this scheme uses only a forward-looking over-reaching zone 2 distance element to identify forward faults.
Ground directional overcurrent functions available in the relay can be used in conjunction with the zone 2 distance
element to increase the coverage for high-resistance faults. Also by default, only a reverse-looking zone 4 distance
element to identify reverse faults. Ground directional overcurrent functions available in the relay can be used in
conjunction with the zone 4 distance element for better time and sensitivity coordination.
For proper operation, the zone 2 and 4 phase and ground distance elements must be enabled, configured, and set per
rules of distance relaying. If used by this scheme, the selected ground directional overcurrent functions must be enabled,
configured, and programmed accordingly.
In single-pole tripping applications, the scheme uses local fault type identification provided by the phase selector together
with information received from the remote terminal.
The scheme generates output operands (

DIR BLOCK TX INIT

and

DIR BLOCK TX1 STOP

through

DIR BLOCK TX4 STOP

) that control

the transmission of signals to the remote end(s). When used with telecommunications facilities, assign the output
operands to operate output contacts connected to key the transmitter at the interface.
The output operands from the scheme (

DIR BLOCK A

,

B

,

C

, and

3P

) must be configured to interface with other relay functions,

output contacts in particular, in order to make the scheme fully operational. Typically, you program the output operand to
initiate a trip, breaker fail, and autoreclose, and drive a user-programmable LED as per user application.
When used in conjunction with the trip output element, the scheme is pre-configured to initiate trip, breaker fail, and
single-pole autoreclose actions.

BLOCK SCHEME BLOCK

— This setting allows the user to assign any FlexLogic operand to block the scheme. Contact inputs

from a pilot cut-out switch are typically used for this purpose.



TRANS BLOCK PICKUP

DELAY: 0.030 s

Range: 0.000 to 65.535 s in steps of 0.001



TRANS BLOCK RESET

DELAY: 0.090 s

Range: 0.000 to 65.535 s in steps of 0.001



BLOCK SCHEME SEAL-IN

DELAY: 0.010 s

Range: 0.000 to 65.535 s in steps of 0.001



GND DIR O/C FWD:

Off

Range: FlexLogic operand



GND DIR O/C REV:

Off

Range: FlexLogic operand



BLOCK SCHEME NO OF

COMM BITS: 1

Range: 1, 2, or 4



BLOCK SCHEME RX1:

Off

Range: FlexLogic operand



BLOCK SCHEME RX2:

Off

Range: FlexLogic operand



BLOCK SCHEME RX3:

Off

Range: FlexLogic operand



BLOCK SCHEME RX4:

Off

Range: FlexLogic operand



BLOCK SCHEME TARGET:

Self-Reset

Range: Self-Reset, Latched, Disabled



BLOCK SCHEME EVENT:

Disabled

Range: Disabled, Enabled

«
...
611
612
613
614
615
...
»

Summary of Contents for L90





































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for L90

Brand: OmarLift Pages: 14

Brand: Microchip Technology Pages: 37

Brand: B&G Pages: 2

Brand: B&K Pages: 9

Brand: Lawler Pages: 6

Brand: Data Aire Pages: 28

Brand: Rachio Pages: 2

Brand: Rane Pages: 2

Brand: Vaillant Pages: 32

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 40

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Vacon Pages: 132

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: National Instruments Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands