Fujitsu F2MC-8L F202RA Hardware Manual Download Page 109

Page: 109 / 436

CHAPTER 4 I/O PORTS

4.4.2

Operations of Port 4 Functions

This section describes the operation of port 4.

■

Operation of Port 4

●

Operation in output port mode

When "1" is written for a bit of the DDR4 register, the bit corresponding to a pin of port 4, the pin functions

as an output port.

In output port mode, the output transistor operation is enabled and output latch data is output to the pin.

By setting the bit corresponding to the pin on the OUT4 register, N-ch open-drain or CMOS push-pull type

can be selected as the output format of the pin.

Once data has been written into the PDR4 register, the written data is held in the output latch and output to

the pin as it is.

The value state of the pin can be read by reading the PDR4 register.

●

Analog input mode setting

Set a bit of the DDR4 register to "0", the bit corresponding to a pin of port 4 assigned for desired analog

input, so that its output transistor is set to OFF and the pin is set at Hi-Z.

Its output latch value can be read by reading the PDR4 register.

Set the bit of the ADEN register of the A/D converter to "1", the bit corresponding to the analog input pin

in use.

●

Operation when a reset is performed

When the CPU is reset, the bits of the PDR4 register are initialized to "1". Thus, the output transistors

become OFF (input port mode) and the pins become Hi-Z.

●

Operation in stop mode

When the pin state setting bit of the standby control register (STBC: SPL) is set to "1" and when the stop

mode is entered, the pin becomes Hi-Z because the output transistor is turned OFF regardless of the value

existing on the DDR4 register in the bit position corresponding to the pin. Input remains fixed to prevent

leaks by input open.

Table 4.4-4 summarizes the operating modes of the pins of port 4.

Table 4.4-4 Operating Modes of Pins of Port 4

Pin name

Normal operation, sleep, stop (SPL = 0)

Stop (SPL = 1)

At a reset

P40/AN0 to P43/AN3

General-purpose I/O port may also serve I/O
for peripherals

Hi-Z

SPL : Pin state setting bit of standby control register (STBC: SPL)
Hi-Z: High impedance

Summary of Contents for F2MC-8L F202RA





















































































































































































































































































































































































































































Search results

Summary of Contents for F2MC-8L F202RA

Reviews:

Related manuals for F2MC-8L F202RA

Brands by name

Popular brands

Fujitsu F2MC-8L F202RA, Hardware Manual

Search results

Summary of Contents for F2MC-8L F202RA

Reviews:

Related manuals for F2MC-8L F202RA

Brands by name

Popular brands