manualshive.com logo in svg

Foerster TAK5-CH1-25, Instruction Manual

The Foerster TAK5-CH1-25 is a versatile and reliable product designed for seamless communication. Unlock the full potential of your device by downloading the free and comprehensive instruction manual from our website. This manual offers step-by-step guidance, ensuring effortless setup and optimal functionality. Access it now at manualshive.com.

Share
Download
background image

4

Table of contents

3.6.1

Notes on how to mount the antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44

3.6.2

Connecting the antenna cable to the motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45

3.7 Mounting the teat  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47
3.8 Filling the heat exchanger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47
3.9 Portion  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48

3.9.1

Adjusting the target (set) and the minimum temperature  . . . . . . . . . . . . . . . . . . . . . . . . . .  48

3.9.2

Setting the parameters for the parallel mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  50
3.9.2.1

Portion dispense with entitlement less than 250 ml . . . . . . . . . . . . . . . . . . . . . . .  50

3.9.2.2

Tolerance values for concentration and milk ratio . . . . . . . . . . . . . . . . . . . . . . . .  50

3.10 Vapour screen for powder outlet, mixer heating and equipment against frost . . . . . . . . . . . . . . . . . .  51
3.11 Filling the milk powder hopper and the milk tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52

3.11.1

Filling the milk powder into the powder hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52

3.11.2

Filling the milk tank  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53

3.12 Calibrating the feed components and the detergent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

4

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

4.1 Overview of the menus in the setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55
4.2 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56
4.3 Time/date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  57
4.4 Machine  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  57
4.5 Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  59
4.6 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  61
4.7 ID-chip  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  61
4.8 Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  61

4.8.1

Feed control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  62
4.8.1.1

Internal stations controlled by the automatic feeder. . . . . . . . . . . . . . . . . . . . . . .  62

4.8.1.2

IFS-F(eeding stations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  63

4.8.1.3

IFS-compact unit for four feeding stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  65

4.8.2

IFS-concentrate stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  67

4.8.3

Scales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  68

4.9 Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  68
4.10 Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  69

5

Device data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  . 71

5.1 Checking and adjusting time/date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71

5.1.1

Checking time/date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71

5.1.2

Adjusting time and date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71

5.2 New installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  72

5.2.1

New installation only of device data, plans, medicine prescriptions, animal data or transmitter 
numbers72

5.2.2

New installation of everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  72

5.3 Restricted mode/ad libitum mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73
5.4 Parallel mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74
5.5 Station parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74

5.5.1

Feeding station  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74
5.5.1.1

Draining time  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  75

5.5.1.2

Entering turn-on and turn-off delay  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  76

5.5.1.3

Pump start and stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  76

5.5.1.4

Maximum speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77

5.5.2

Concentrate stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77

5.5.3

Teat slider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77

5.5.4

CalfProtect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77

5.6 Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  78

5.6.1

Mixer draining  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  78
5.6.1.1

Mixer draining valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  78

Summary of Contents for TAK5-CH1-25



































































































































































































































Reviews:

No comments

Related manuals for TAK5-CH1-25

Makerfire N10 Instructions Manual preview
N10
Brand: Makerfire Pages: 10
Tacx Cosmos Assembling Instructions preview
Cosmos
Brand: Tacx Pages: 2
C.E. Nierhoff & Co C520 Troubleshooting Manual preview
C520
Brand: C.E. Nierhoff & Co Pages: 7
Elation SATURA SPOT LED PRO User Manual preview
SATURA SPOT LED PRO
Brand: Elation Pages: 41
Tapco 4400 Service Manual preview
4400
Brand: Tapco Pages: 16
Zenbooth Solo Build Instructions preview
Solo
Brand: Zenbooth Pages: 40
10x Genomics Visium CytAssist User Manual preview
Visium CytAssist
Brand: 10x Genomics Pages: 51
10x Genomics Chromium X Series Quick Start Manual preview
Chromium X Series
Brand: 10x Genomics Pages: 5
Bahco BH6 Service Manual preview
BH6
Brand: Bahco Pages: 9
ZIGBEE 622 Quick Start Manual preview
622
Brand: ZIGBEE Pages: 6
Daisy DMR Installation Manual preview
DMR
Brand: Daisy Pages: 2
Daisy Below Ground Pool Cover Box Installation Manual preview
Below Ground Pool Cover Box
Brand: Daisy Pages: 3
Eaton X10 Installation Manual preview
X10
Brand: Eaton Pages: 21
NANO Pulsar Operating Instructions preview
Pulsar
Brand: NANO Pages: 4
IBS Scherer M-500 Translation Of The Original Instructions preview
M-500
Brand: IBS Scherer Pages: 64
Hammer Strength MTSP Unpacking And Assembly Instructions preview
MTSP
Brand: Hammer Strength Pages: 18
Major tech MT550 Instruction Manual preview
MT550
Brand: Major tech Pages: 12
Rational iVario Pro L Original Installation Instructions preview
iVario Pro L
Brand: Rational Pages: 60

Brands by name

Popular brands

Load more brands