Foerster TAK5-CH1-25 Instruction Manual Download Page 143

Page: 143 / 226

Cleaning

143

cleaning

heat exchanger

2. Confirm

start?

with

3. Change the detergent quantity, if necessary, and confirm with

9.4

Circuit cleaning

The heat exchanger, the suction hoses and the milk hose can be

simultaneously cleaned with detergent.

cleaning

circuit cleaning

2. In

water amount

enter the desired water quantity for pre-

cleaning and rinsing.

3. Confirm

start?

with

4. Change the detergent quantity, if necessary, and confirm with

The automatic feeder starts pre-cleaning.

After a short time pre-cleaning is broken off. The message on the

right is displayed:

Note

: heat exchanger is automatically cleaned twice a

day, at 7:00 a.m. and at 10:00 p.m. Max. four cleaning

cycles can be carried out. The default values of the

cleaning times can be changed at any time.

cleaning

...

circuit cleaning

...

circuit cleaning

start?

water amount: 2 L

Default value:

2 L

Range:

1 L to 10 L

Note

: The longer the hoses, the larger should be the wa-

ter quantity for pre-cleaning and rinsing.

circuit cleaning

detergent: 0 ml/L

hoses

disconnected?

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands