Foerster TAK5-CH1-25 Instruction Manual Download Page 126

Page: 126 / 226

126

Feeding

8.5

Additive dispense

To dispense medicine and electrolyte up to two additive dispens-

ers can be connected to the automatic feeder: A dispenser for

powder or liquid additives and one further solely for liquid addi-

tives.

You can determine the dosage of medicine/electrolyte and the

duration of administration in the prescription plans. Up to four

prescription plans for medicine and one prescription plan for

electrolyte can be created. Medical preparations are dosed into

the milk or milk powder/water mix, whereas electrolytes are nor-

mally dosed into the water.

Additive

contains the following menus:

•

Animal

•

Group

•

Medicine prescription

•

Electrolyte prescription

feeding

...

additive

...

Note:

The electrolytes can also be given according to

the medicine prescription plan. In that case, the electro-

lytes are dosed into the milk or milk powder/water mix

like the medical preparations.

additive

animal

group

medicine prescr.

electrolyte prescr.

Note:

Please observe the indications on the package in-

sert and discuss the dosage with the veterinary, if nec-

essary.

Warning:

Additives can be harmful to health. Therefore,

make sure that only authorized persons have access to

them.

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands