Foerster TAK5-CH1-25 Instruction Manual Download Page 171

Page: 171 / 226

Failures and warnings

171

12 Failures and warnings

When a

failure

occurs, the

automatic mode is broken off

. The

display shows the corresponding failure message and the green

LED on the hand-held terminal starts flashing.

Warnings

signal a problem but they

do not break off the auto-

matic mode

. Also with warnings the LED starts flashing.

Various warnings and failures are automatically deleted as soon

as the fault has been removed. Some of them are deleted only

after you have pressed

delete failure?

resp.

delete warning?

Irrespective of the failures and warnings, messages are gener-

ated e.g. by hand-held terminal or the bootloader of the auto-

matic feeder control and displayed on the screen. These

messages are explained in section „

Other failures and mes-

sages

“.

12.1 Failures

12.1.1

CRC-error

If the memory datasets of the automatic feeder control have

been destroyed, the message on the right will be displayed.

Note

: Those warnings which have been deleted or hid-

den with

will be automatically displayed again after

one further warning has been displayed but anyway af-

ter ten minutes at the latest.

Note

: Please consider the documentation of the periph-

eral devices, if required.

failure

CRC-error

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands