manualshive.com logo in svg

Foerster TAK5-CH1-25, Instruction Manual

Share
Download
Foerster TAK5-CH1-25 Instruction Manual Download Page 177

Failures and warnings

177

12.1.8

Heating

If the heating does not work properly, the reasons for it may be 

the following:

> In 

on?

 press 

. Check whether the displayed temperature  

increases.

> If the temperature increases, in 

delete failure?

 press 

.

Exclusively for service personnel:

•

The heating element is defective.

> Check the heating element for continuity.

•

The temperature sensor is defective.

•

There is no voltage on the heating.

> Check the on-site fuses, if necessary.

•

The safety temperature limiter is triggered. To reactivate it, 

proceed as follows:

failure

heating

heating

on?

boiler:         xx.x 

o

C

delete failure?

1. In 

delete failure?

 press 

.

2. Pull the mains plug. For those devices with 

fix power connection, switch the main 

switch off and be sure the device is free of 

voltage before getting close to live parts.

3. Open the right lateral door of the automatic 

feeder. Remove the metal covering.

4. Push the Reset-button to reset the safety 

temperature limiter.

Summary of Contents for TAK5-CH1-25



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands