Foerster TAK5-CH1-25 Instruction Manual Download Page 139

Page: 139 / 226

Cleaning

139

Cleaning

The automatic feeder has to be cleaned at regular intervals, par-

ticularly when fresh milk is fed. The following cleaning menus

can be selected:

•

Mixer

•

Heat exchanger

(serial equipment with

)

•

Circuit cleaning

•

Air

(pulsating compressed-air cleaning)

•

(

Box) valves

•

Sponge

(= heat exchanger cleaning with sponge)

•

Hose

•

Settings

9.1

Settings

In this menu you can enter:

•

the temperature of the cleaning water,

•

the detergent quantity,

•

whether the teat should be cleaned.

cleaning

settings

cleaning

mixer

heat exchanger

circuit cleaning

air

valves

sponge

hose rinsing

settings

Note:

certain failures prevent the start of cleaning pro-

cesses, e.g. when water or detergent have not been cal-

ibrated yet.

Type and frequency of the cleaning process depend on

the composition and the germ-content of the milk to be

fed.

Warning

: Detergent can be harmful to health. Therefore

make sure that only authorized persons have access to

it.

settings

temperature: [45]°C

detergent: 0 ml/L

clean teat: no

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands