Foerster TAK5-CH1-25 Instruction Manual Download Page 72

Page: 72 / 226

Device data

5.2

New installation

When (re)commissioning the automatic feeder, the program

(software) must be completely reset, i.e. redundant data and out-

dated inputs resp. misentries are removed from the memory.

Animal data

are defined as e.g. group membership, housing

date, feeding days and total consumption.

Device data

are defined as e.g. feeding and concentration

plans.

5.2.1

New installation only of device data, plans, medicine pre-
scriptions, animal data or transmitter numbers

device data

new installation

2. Press

device data

3. Confirm

device data, new installation?

with

4. With the menus

plans, medicine prescription, animal data

resp.

transmitter

proceed as with

device data

5.2.2

New installation of everything

device data

new installation

2. In

everything

press

3. Confirm

everything new installation?

with

Note:

After you have changed the date, switch the auto-

matic feeder off and then on to immediately carry out daily

calculation.

new installation

device data

plans

medicine prescr.

animal data

transmitter

CalfProtect

everything

Note

: When carrying out „new installation“ all the

animal

data

as well as the

medicine

and

electrolyte prescrip-

tions

are deleted, the

transmitter numbers

are set to

zero and the

device data

are overwritten by default val-

ues.

new installation

device data

...

device data

new installation?

everything

new installation?

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands