manualshive.com logo in svg

Foerster TAK5-CH1-25, Instruction Manual

Share
Download
Foerster TAK5-CH1-25 Instruction Manual Download Page 52

52

Start-up

The heating cable is activated as soon as the temperature falls 

below 3 ºC. It protects e.g. the hose pipes, the training pump and 

the fittings against frost.

The heating cable becomes necessary when the automatic 

feeder is installed in an unprotected location or it is exposed to 

extreme cold.

Solely for service personnel

:

3.11

Filling the milk powder hopper and the milk tank

3.11.1

Filling the milk powder into the powder hopper

Danger! 

Hazardous voltage! Electric shock haz-

ard!

The automatic feeder must be free of voltage be-

fore opening the rear cover behind which are lo-

cated the processor and the relay power board. 

To do so, pull the mains plug.

Warning!

Automatic start-up!

Before carrying out any kind of operations on or inside the pow-

der hopper, make sure that the automatic feeder is free of volt-

age. To do so, pull the mains plug.

Note:

 There is no warning when the powder hopper is emp-

ty! The automatic feeder will continue to feed without milk 

powder. This may effect that the animals are only fed with 

water, thus being not or insufficiently provided with feed.

Only fill in milk powder that is suitable for calf feeding.

Summary of Contents for TAK5-CH1-25



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands