Foerster TAK5-CH1-25 Instruction Manual Download Page 198

Page: 198 / 226

198

Check list for after-sales service

2.5.6

Circulation valve available yes/no

2.5.7

Cleaning valve available yes/no

2.5.8

Air valve (pulsating compressed air cleaning) available yes/no

2.5.9 Circulation pump available yes/no

2.5.10 Mixer sensor available yes/no

2.5.11

Water meter available yes/no

2.5.12

Spot and supply electrode available yes/no

2.5.13

MilkMaker-dispensing unit available yes/no

Heating activated yes/no - Relay

mechanical/

electronical

Select the identification system, if necessary.

ID-chip

Stations

6.1

Activate the internal feeding station(s) controlled by the automatic feeder.

6.2

Configure the IFS-feeding station(s). Select the options, if available.

Allocate the CAN-bus address to the IFS-feeding station(s): To do so, put the IFS (feeding station)
in the search-mode and allocate the address via search?.

6.3

Configure the IFS-compact unit(s) and assign the CAN-bus address: To do so, put the IFS-

compact unit in the search mode and allocate the address via search?.
Allocate each of the four pumps to a station and the equipment of the station.

6.4

Configure the IFS-concentrate station 1(...). Select the type of concentrate and of concentrate

feeder. Assign the CAN-bus address: To do so, put the IFS (C-station) in the search mode and al-
locate the address via

search

6.5

Configure the scales control 1/x. To do so, select the CAN-address via the DIP-switch on the

scales control board and enter the selected address into setup. Activate the available weighing
units (1/2).

Terminal

Communication

8.1

PC serial/CAN, Institute yes/no

8.2

Printer no/serial/CAN

Device data

New installation

Select the restricted or the ad libitum mode.

Feeding station

3.1

Draining and hold time

3.2

Enter the turn-on and turn-off delay in case of gradient or servo control.

3.3

Enter the minimum and maximum speed in case of servo control (with IFS-feeding station).

3.4

Enter pump start and stop in case of servo control (with IFS-feeding station).

3.5

Parallel mode: Switch the automatic calibration on or off, determine the time of automatic cal-

ibration.

Teat slider (close / open after xx min)

CalfProtect (open after xx min)

Select the mixer options (drain/OFF delay)

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands