Foerster TAK5-CH1-25 Instruction Manual Download Page 69

Page: 69 / 226

Setup

4.10 Communication

If you want to connect a PC to the automatic feeder, here you

can select whether your PC shall exchange the data with the

automatic feeder via a serial or a CAN-interface (via the

Förster-gateway). If you want to use the institute program,

which is intended to record the data relating to animals’ visits, in

institute

select

yes

Printer

•

Serial: Select this option if a commercially available printer is

connected to the automatic feeder via a serial interface.

•

CAN: Select this option if the print data have to be transferred

via the CAN-bus.

terminal

address: [1]

Note:

Within a CAN-bus system an address can be allo-

cates only once.

setup

...

communication

PC: CAN

institute: no

printer: [ no]

Note:

If you want to update the control program of the au-

tomatic feeder by means of the update set, basically here

serial

must be selected.

communication

PC: serial

printer: [ no]

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands