Foerster TAK5-CH1-25 Instruction Manual Download Page 184

Page: 184 / 226

184

Failures and warnings

3. If the IFS is detected on the CAN-bus, the address will be

transferred. The message on the right will be displayed. The

green LED (ST1 or H4) of the IFS-motherboard does not blink

anymore.

12.2.5

Motor F-station

This message is displayed if the motor of the IFS-feeding station

does not deliver any counting pulses anymore. A potential rea-

son for it may be the following:

1. The motor which starts the peristaltic pump does not run any-

more. Press

in the submenu

pump: start?

to check it.

2. The cable between the motor and the board used to transfer

the pulses has been possibly removed or it may be defective.

12.2.6

IFS-C(oncentrate station)

This message is displayed if the automatic feeder is not able to

communicate with the control of the IFS-concentrate station via

the CAN-bus. A reason for it may be that the CAN-node is

switched off or the address of the IFS-C does not correspond to

the one in the automatic feeder.

see

4.8.2

IFS-concentrate stations, page

12.2.7

Motor C-station

This message is displayed if the motor of the IFS-concentrate

station does not deliver any counting pulses anymore. A poten-

tial reason for it may be the following:

1. The motor, which starts the auger of the concentrate feeder

does not run anymore. Press

in the submenu

motor:

start?

to check it.

IFS-F

found!

Note:

If you have activated the

search mode

by mistake,

repress the button S5 or H4. The search mode will be

ter-

minated

warning

motor F-station

<station 7>

pump: start?

warning

IFS-C

<IFS-C 1>

search?

warning

motor C-station

<station 7>

motor: start?

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Brands by name

Popular brands