Foerster TAK5-CH1-25 Instruction Manual Download Page 45

Page: 45 / 226

Start-up

animal. Block the area next to the feeding station, if neces-

sary.

If an antenna identifies two animals simultaneously, animal iden-

tification will be disrupted for both animals.

> The distance between two antennas should be approx. 100

cm, in order to avoid overlaps of the identification range. In

case of double or foreign identifications, you have to screen

the antennas by means of grounded plates.

3.6.2

Connecting the antenna cable to the motherboard

Only

service personnel

is allowed to connect the antenna

cables.

1. Remove the casing cover of the control unit.

Caution

: Lay out the antenna cables in such a way that

they are not damaged by the animals.

1 Cable of the hand-held terminal

3 Antenna cable of feeding station 2

2 Antenna cable of feeding station 1

4 Cable clamps

Danger!

Hazardous voltage! Electric shock

hazard.

Pull the mains plug.

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands