manualshive.com logo in svg

Festo CMMP-AS-***-M0 Series, Manual

Share
Download
Festo CMMP-AS-***-M0 Series Manual Download Page 162

6

Device Control

162

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

statusword

Bit

Function

Description

5

quick_stop

If the bit is deleted, the drive carries out a Quick Stop in

accordance with quick_stop_option_code.

7

warning

This bit shows that a warning is active.

8

drive_is_moving

This bit is set independently of modes_of_operation when the

current actual speed (velocity_actual_value) of the drive is

outside the related tolerance window (velocity_threshold).

9

remote

This bit shows that the output stage of the motor controller can

be enabled via the CAN network. It is set when the controller

enable logic is correspondingly set via the object enable_logic.

10

Dependent on modes_of_operation.

target_reached

In the Profile Position Mode:

The bit is set when the current target position is reached and the

current position (position_ actual_value) is located in the

parametrised position window (position_window). 

It is also set when the drive comes to a standstill with Stop bit

set.

It is deleted as soon as a new target is specified.

In the Profile Velocity Mode

The bit is set when the speed (velocity_actual_value) of the

drive is in the tolerance window (velocity_window,

velocity_window_time).

11

internal_limit_active

This bit shows that the I

2

t limitation is active.

12

Dependent on modes_of_operation.

set_point_acknowledge

In the Profile Position Mode

This bit is set when the motor controller has recognised the set

bit new_set_point in the controlword. It is deleted again after

the bit new_set_point in the controlword has been set to zero.

 for this, see unconditionally also chapter 7.3

speed_0

In the Profile Velocity Mode

This bit is set when the current actual speed

(velocity_actual_value) of the drive is within the related

tolerance window (velocity_threshold).

homing_attained

In the Homing Mode:

This bit is set when homing has been ended without error.

ip_mode_active

In the Interpolated Position Mode:

This bit shows that interpolation is active and the interpolation

data records are being evaluated. It is set when requested by

the bit enable_ip_mode in the controlword. 

 unconditionally

also chapter 7.4.

Summary of Contents for CMMP-AS-***-M0 Series







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands