Festo CMMP-AS-***-M0 Series Manual Download Page 125

Page: 125 / 294

Setting parameters

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

125

Value

Measurement file

[X2A]

[X2B]

[X10]

Selection as position actual value encoder is only possible between the encoder input

[X10] and the respective commutation encoder [X2A] or [X2B]. It is not possible to use the

configuration [X2A] as commutation encoder and [X2B] as position actual value encoder,

or vice versa.

Object 2022

: synchronisation_encoder_selection

The object synchronisation_encoder_selection specifies the encoder input that is used as synchronisa

tion setpoint value. Dependent on the operating mode, this corresponds to a position setpoint (profile

position mode) or a speed setpoint (profile velocity mode).

Only [X10] can be used as synchronisation input. As a result, selection can be made between [X10] and

no input. The same input should not be selected as synchronisation setpoint as for the actual value

encoder.

Index

2022

Name

synchronisation_encoder_selection

Object Code

VAR

Data Type

INT16

Access

PDO mapping

Units

–

Value Range

-1, 2 (

table)

Default Value

Value

Measurement file

-1

No encoder / undefined

[X10]

Object 202F

: synchronisation_selector_data

Activation of a synchronous setpoint can take place through the object synchronisation_main. For the

synchronous setpoint to be calculated at all, bit 0 must be set. Bit 1 permits activation of the synchron

ous position through starting of a position record. Currently, only 0 can be parametrised, so the syn

chronous position is always switched on. Through bit 8, it can be established that homing should take

place without activation of the synchronous position so that the master and slave can be referenced

separately.

Summary of Contents for CMMP-AS-***-M0 Series







































































































































































































































































































Search results

Summary of Contents for CMMP-AS-***-M0 Series

Reviews:

Brands by name

Popular brands

Festo CMMP-AS-***-M0 Series, Manual

Search results

Summary of Contents for CMMP-AS-***-M0 Series

Reviews:

Brands by name

Popular brands