Extron electronics MLC 104 IP Plus Series, User Manual, Page: 82 / 174

MLC 104 IP Plus Series • SIS
™
Programming and Control 74
X2@
= Verbose/tagged response mode status:
NOTE: In verbose/response mode, the device
(the MLC) responds with more information than
it usually would. For example, the MLC can
send out a notice of a change in some setting
without receiving a query via your PC. That
change could have been a result of an internal
process (a script execution), a selection made
using a touchpanel or keypad, a change
made using GV or a web page, or input from a
connected sensor or switch.
That is an example of a verbose (wordy)
relationship between the controller and a
connected device. Verbose mode creates
more network traffic than usual, which can
slow down network performance.
0 = clear, default for Telnet connections
1 = verbose mode is on (enabled)
2 = verbose mode is off, tagged responses are
sent for queries (tagged responses are enabled)
3 = verbose mode is on (enabled) and tagged
responses are enabled and sent for queries
X2@
value
0
1
2
3
Receive unsolicited
responses
(messages)
for all actions
initiated via any source
(touchpanel, port input,
internal web page
changes, or
commands)
instead of only for SIS
commands
Verbose
Responses
Receive tagged
responses to
read/view
requests
(Responses to SIS
commands are always
tagged.
Turning tagged
responses on adds
tags to the responses
to SIS read requests.)
Tagged
Responses
See the verbose mode command (
E
CV
}
)
on page 88 within the IP commands section
in the command/response table for a brief
explanation of what this communication mode is
and what it does.
NOTE:
If tagged responses are enabled, all read
commands return the constant string and the
data or value, the same as in responses for
setting a value. For example, for
E
CN
}
,
the response is Ipn •
X1@ ]
rather than just
the data (
X1@ ]
).
X2#
= Priority status for receiving timeouts:
0 = use send data string command
parameters (0 = default)
1 = use configure receive timeout
command parameters
X2%
= Baud rate: 300, 600, 1200, 1800, 2400, 3600,
4800, 7200, 9600 (default), 14400, 19200,
28800, 38400, 57600, or 115200
X2^
= Parity (only the first letter is needed):
O = odd
E = even
N = none (default)
M = mark
S = space
X2&
= Data bits: 7, 8 (default = 8)
X2*
= Stop bits: 1, 2 (default = 1)
X3#
= Password (minimum length = 4 characters,
maximum length = 12 characters)
No special characters are allowed: use alpha-
numeric characters. Passwords are case sensitive.
Disallowed characters are shown below.
Character Hex Dec
Space 20 32
‘ “ Quotation marks 22 34
< “Less than” symbol 3C 60
> “Greater than” symbol 3E 62
# Pound (hash mark) 23 35
% Percent 25 37
{ Left curly brace 7B 123
} Right curly brace 7D 125
| Vertical bar / pipe 7C 124
\ Backslash 5C 92
^ Caret 5E 94
~ Tilde 7E 126
[ Left square bracket 5B 91
] Right square bracket 5D 93
` Grave accent 60 96
NOTE: A user password cannot be assigned if no
administrator password exists; the E14 error
code is returned. If the administrator password
is cleared, then the user password is also
removed.
X3$
= Daylight saving time (DST) is a region-specific 1-hour
offset that begins in spring and ends in fall.
0
= off/ignore (default)
1 = USA on – DST begins on the second
Sunday of March at 2 AM and ends at 2 AM
on the first Sunday of November. For example,
time in California is GMT -8:00 from March to
November and GMT -7:00 from November to
March. However, DST should be turned off in
Hawaii, American Samoa, Guam, Puerto Rico,
the Virgin Islands, the eastern time zone portion
of the state of Indiana, and the state of Arizona
(excluding the Navajo Nation).
2 = Europe on – begins on the last Sunday in
March, ends on the last Sunday in October. DST
should be turned off for Iceland.
3
= Brazil on
X3%
= Event number: 0 - 99
This is valid only while events are running.
X4)
= I/O mode
0 = input (default)
1 = output
2 = input and pull-up resistor
3 = output and pull-up resistor