manualshive.com logo in svg

Extron electronics MLC 104 IP Plus Series, User Manual, Page: 166 / 174

Share
Download
Extron electronics MLC 104 IP Plus Series User Manual Download Page 166

MLC 104 IP Plus Series • Firmware Updates

158

6. 

In the 

Choose File to Upload

 dialog box, locate and select the firmware file (*.

s19

) 

you downloaded to 

C:\Program Files (x86)\Extron\Firmware\MLC_104_

IP_PLUS\

xx

, and click the 

Open

 button.

7. 

Click 

Upload

 button on the web page to upload the firmware to the controller. It takes a 

while to load the file into the controller. You do not see any on-screen indication when 
the upload has finished. Once the firmware upload is completed, the MLC performs a 
reset.

8. 

If needed, see 

Resetting the Unit

 starting on page 31 in the “Installation” 

section and see the 

Global Configurator Help

 file for instructions on how to restore a 

configuration.

Updating Firmware Via Extron Firmware Loader Software

This method allows you to update one MLC at a time via IP or RS 232 communication using 
Firmware Loader software (available free from 

www.extron.com

).

NOTE:

  The MLC 104 IP Plus requires Firmware Loader version 4.0 or higher.

1. 

If not already installed, download Firmware Loader from the Extron website and follow 
the on-screen instructions to install it.

2. 

Download the 

.s19

 firmware file to the PC.

3. 

Start the Firmware Loader (FWLoader, 

 ) software on the connected PC. The 

Add 

Device

 dialog box opens.

4. 

In the 

Add Device

 dialog box, choose the type of device (MLC 104 IP Plus).

5. 

Select the communication type (connection method) and settings.

• 

For 

IP communication

, select 

TCP/I

, enter the IP address of the controller, 

verify or change the Telnet port number, and enter an administrator password if a 
password has been set for the unit. 

NOTE:

  Passwords must contain 4 to 12 alphanumeric characters. Symbols 

and spaces are not allowed, and the passwords are case-sensitive.

• 

For 

serial communication

, select 

RS-232

 and set the communications settings 

to 38400 baud.

6. 

Click the 

Connect

 button. If the connection is unsuccessful, an error message or 

timeout message is displayed. If the connection is successful, the model name is 
displayed within the dialog box and the 

New Firmware File 

panel becomes 

accessible.

7. 

Click the 

Browse

 button. The 

Open

 window appears.

8. 

Locate and select the firmware file on your PC that you downloaded for the MLC, then 
click the 

Open

 button. The 

Open

 window closes.

9. 

Click 

Add

. The 

Add Device

 dialog box closes, and the MLC you just added appears in 

the device list within the main Firmware Loader window. The version of the currently installed 
firmware, the name of the firmware file you selected to load onto the unit, and the IP address 
are also listed.

10. 

With that MLC unit selected, click 

Begin

. The PC uploads the new firmware to the MLC. 

Once the firmware is uploaded, the MLC restarts events.

11. 

Firmware Loader displays the new firmware version in the 

Firmware

 column.

Summary of Contents for MLC 104 IP Plus Series















































































































































































Reviews:

No comments