manualshive.com logo in svg

Extron electronics MLC 104 IP Plus Series, User Manual, Page: 42 / 174

Share
Download
Extron electronics MLC 104 IP Plus Series User Manual Download Page 42

MLC 104 IP Plus Series • Software-based Configuration and Control

34

Software-based 
Configuration and 
Control

This section of the guide is divided into the following topics:

• 

Configuration and Control: an Overview

• 

The Basic Setup Steps: a Guide to this Section and Other Resources

• 

Communicating with the MLC

• 

Configuring the MLC for Network Communication

• 

Global Configurator Software for Windows

 

• 

Advanced Configuration

• 

Controlling an MLC 104 IP Plus

• 

Customizing the MLC Control Web Pages

• 

Troubleshooting

NOTE:

  In images of software or web pages, circled numbers correspond to the like-

numbered procedural steps.

Configuration and Control: an Overview

An MLC 104 IP Plus Series controller 

must

 be configured before use in order to recognize 

and accept commands and pass them on to the controlled devices. It can be configured 
and controlled via a host computer attached to the right/rear panel LAN (local area network) 
port (preferred) or the front panel Config port. 

NOTE:

  Extron recommends configuring and controlling the MLC via the LAN connector. 

Ethernet connections are faster and more reliable than RS-232 connections.

• 

The primary means for configuring the controller is by using the Extron Global 
Configurator (GC) software. This method requires a properly configured PC with  
Windows XP or a higher version of Windows installed. Global Configurator generates 
GlobalViewer web pages that are uploaded to the MLC and can be used to control the unit 
and make adjustments to its settings.

NOTE:

 Microsoft

®

 Internet Explorer

®

 is currently the only web browser that fully 

supports GlobalViewer pages.

• 

Alternatively the default web pages embedded within the MLC provide a means to 
perform some setup, adjustment, and control via a web browser from any type of 
network-enabled computer.

Summary of Contents for MLC 104 IP Plus Series















































































































































































Reviews:

No comments