Covidien Newport e360 Service Manual Download Page 68

Page: 68 / 154

Component Removal and Replacement

4-8

Service Manual



Note:

If the main board GR-PCB2100A is replaced, the ventilator software must be reloaded, and d1, d2, d4, and d9
calibrations performed. Refer to section

2.10

for the

Software Upgrade Procedure

and Chapter

for calibration

procedures.

4.8.2

Main Board Support (CVR2103M)

Figure 4-5.

Main Board Support (CVR2103M)

To remove and reinstall the main board support, refer to

Figure 4-5.

and perform the following

steps:

Remove the front panel assembly by performing the procedure in section

4.7

, “

Front Panel Assembly

.”

Remove cable GR-CBL2121A from J4 on GR-PCB2100A.

Remove cables GR-CBL2137A and GR-CBL2138A from the top LEDs.

Remove the four screws (two on each side) and washers (two on each side) securing the main board
support to the front panel assembly.

Carefully lift up on the main board support, and feed cables GR-CBL2155A and GR-CBL2121A through
the cutout on the main board support.

Place the main board support with the main board in an ESD-safe container.

Reinstall the main board support by reversing steps 2 through 6.

Screws

GR-CBL2121A connected to J4 on GR-PCB2100A

CVR2103M

Main board (GR-PCB2100A)

GR-CBL2137A and GR-CBL2138A

Summary of Contents for Newport e360



























































































































































Search results

Summary of Contents for Newport e360

Reviews:

Related manuals for Newport e360

Brands by name

Popular brands

Covidien Newport e360, Service Manual

Search results

Summary of Contents for Newport e360

Reviews:

Related manuals for Newport e360

Brands by name

Popular brands