manualshive.com logo in svg

Covidien Newport e360, Service Manual

Share
Download
Covidien Newport e360 Service Manual Download Page 61

 4-1

4 Component Removal and Replacement

4.1

Overview

This chapter provides procedures for removing and replacing various components of the 
Newport™ e360 ventilator.

4.2

Key Components

4.2.1

Ordering

To order a component, refer to 

Table B-1.  

for the appropriate part number. Note that 

Table B-

1.  

lists two part numbers for each component: a manufacturing part number and a service part 

number. The manufacturing part number is printed on the part; the service part number is 
needed to order the required spare part. For some components, the service part number is 
different from the manufacturing part number.

The manufacturing part number for each component is referenced throughout this manual.

4.2.2

Removing

Unless instructed otherwise, reinstall parts by reversing the disassembly procedure.

4.3

Preparation

Before repairing or servicing the ventilator, perform the following steps:

1.

Disconnect the power.

2.

Shut off or disconnect the air and oxygen gas supplies.

3.

Put on an ESD wrist strap. Perform procedures in an ESD-safe environment.

4.4

Tools Required

•

#0 Phillips screwdriver

Summary of Contents for Newport e360



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands