manualshive.com logo in svg

Covidien Newport e360, Service Manual

Share
Download
Covidien Newport e360 Service Manual Download Page 64

Component Removal and Replacement

4-4 

 Service Manual

4.5.2

Exhalation Flow Sensor Cable (Outside) (GR-CBL2123P)

To replace the exhalation flow sensor cable, perform the following steps:

1.

Remove the exhalation valve and exhalation flow sensor by following the steps in section 

4.5.1

, “

Valve 

(EXH2105A) and Flow Sensor (FLS2101P)

.”

2.

Remove the exhalation flow sensor cable (outside) (GR-CBL2123P) from the exhalation manifold by 
pulling the collet of the cable connector.

Note:

The lock mechanism of the connector can be easily released by pulling the collet of the connector. Do NOT 
disconnect the connector by pulling the wire.

3.

Reinstall the cable to the exhalation manifold by aligning the key on the connector with the notch of the 
female connector on the exhalation manifold.

4.6

Top Cover (CVR2101M)

Figure 4-2.  

Top Cover

1

Screws (three of six securing cover to ventilator)

Summary of Contents for Newport e360



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands