Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300196-01
Printed in U.S.A.
Form 30XV-3T
Pg CL-1
6-19
Replaces: New
START-UP CHECKLIST FOR 30XV LIQUID CHILLERS
(Remove and use for Job File)
A. PROJECT INFORMATION
Job name
_____________________________________
Address
_____________________________________
City ______________________State ____Zip_________
Equipment tag/mark for____________________________
Installing contractor_______________________________
Sales office _____________________________________
Start-up performed by_____________________________
Design Information
Unit
Model ____________________________________ Serial________________________________________
Compressors
Compressor A
Model ____________________________________ Serial ________________________________________
Compressor B
Model ____________________________________ Serial________________________________________
Evaporator
Model ____________________________________ Serial ________________________________________
B. PRELIMINARY EQUIPMENT CHECK (This section to be completed by installing contractor)
1. Is there any physical damage?
Yes
No
Will this prevent start-up?
Yes
No
Description:
2. Unit is installed level as per the installation instructions.
Yes
No
3. Power supply agrees with the unit nameplate.
Yes
No
4. Correct control voltage ________vac.
Yes
No
5. Electrical power wiring is installed properly.
Yes
No
6. Unit is properly grounded.
Yes
No
7. Electrical circuit protection has been sized and installed properly.
Yes
No
8. All terminals are tight.
Yes
No
9. All plug assemblies are tight.
Yes
No
10. All cables, thermistors and transducers have been inspected for cross wires.
Yes
No
11. All thermistors are fully inserted into wells.
Yes
No
12. Oil separator heaters energized for 24 hours before start-up.
Yes
No
13. Relief valve vent piping per local codes.
Yes
No
NOTE: To avoid injury to personnel and damage to equipment or
property when completing the procedures listed in this start-up
checklist, use good judgment, follow safe practices, and adhere
to the safety considerations/information as outlined in preced-
ing sections of this Controls, Start-Up, Operation, Service and
Troubleshooting document.
CAPACITY
EWT
LWT
FLUID TYPE
FLOW RATE
P.D.
AMBIENT
Evaporator
Summary of Contents for AquaForce 30XV140
