Canon imageRUNNER ADVANCE C3500 III Series, Service Manual, Page: 430 / 1252

E590-8002-02 Error in the Punch Motor (Puncher Unit-A1)
Detection Description The Punch HP Sensor does not detect the punch during initialization.
The Punch HP Sensor does not detect the punch when the Punch Motor has been driven for 0.4
seconds for returning the punch after the punch jam.
Remedy
Puncher Unit-A1
[Related parts]
- Harnesses from the Punch HP Sensor 1 (PS303) to the Puncher Relay PCB
- Harnesses from the Punch HP Sensor 2 (PS304) to the Puncher Relay PCB
- Harnesses from the Punch Motor Clock Sensor (PS305) to the Puncher Relay PCB
- Harnesses from the Punch Motor (M301) to the Puncher Relay PCB
- Punch HP Sensor 1 (PS303)
- Punch HP Sensor 2 (PS304)
- Punch Motor Clock Sensor (PS305)
- Punch Motor (M301)
- Puncher Relay PCB (PCB302)
- Puncher Controller PCB (PCB301)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
E593-8001-02 Error in the Punch Shift Motor (Puncher Unit-A1)
Detection Description The punch unit does not come off the Punch Slide HP Sensor when shifting the punch unit by 9mm
toward rear.
Remedy PUNCHER UNIT-A1
[Related parts]
- Harnesses from the Punch Slide HP Sensor (PS302) to the Puncher Controller PCB
- Harnesses from the Punch Shift Motor (M302) to the Puncher Controller PCB
- Punch Slide HP Sensor (PS302)
- Punch Shift Motor (M302)
- Puncher Controller PCB (PCB301)
- Finisher Controller PCB (PCB101)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
E593-8002-02 Error in the Punch Shift Motor (Puncher Unit-A1)
Detection Description The Punch Slide HP Sensor does not detect the punch unit when shifting the punch unit by 37mm
toward front.
Remedy Puncher Unit-A1
[Related parts]
- Harnesses from the Punch Slide HP Sensor (PS302) to the Puncher Controller PCB
- Harnesses from the Punch Shift Motor (M302) to the Puncher Controller PCB
- Punch Slide HP Sensor (PS302)
- Punch Shift Motor (M302)
- Puncher Controller PCB (PCB301)
- Finisher Controller PCB (PCB101)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
7. Error/Jam/Alarm
408