Axis 7100 User Manual Download Page 144

Page: 144 / 181

Troubleshooting

AXIS 7100 User’s Manual

144

Illegal LDAP filter specified

Invalid LDAP filter. Please enter a new value.

User and password are
required to connect to this
LDAP server

Please enter your username and password.

User and password can not
be used to connect to this
LDAP server

This LDAP server does not accept requests with the
specified username and password.

No destinations were
retrieved

No destinations were retrieved. Change your LDAP set-
tings and try again.

LDAP error! No/several e-
mail address(es) were
retrieved

The user could not be authenticated by the LDAP serv-
er. Change the LDAP settings and try again.

Missing mandatory FTP
parameter for external
address book

Check the FTP settings for the external address book
and try again.

Scanner not
connected

Please check the scanning device connection and try
again.

Scanner not
supported

The attached scanning device is not supported. Digital
copying/scanning will not work properly.

Scanning failed

An error occurred whilst sending. Please refer to earlier
messages.

Illegal queue for:

The specified LPD print queue does not exist; check
spelling and syntax.

Illegal command for (The
printer may be busy):

Incorrect LPD Mode selected for the specified printer
destination.

Incorrect Value

The entered value does not match the pattern speci-
fied by the administrator.

Meta Data enabled.
Keyboard Required

The meta Information functionality is enabled and re-
quires that a keyboard is connected.

Could not connect to
Windows NT domain
controller

The name or the IP address may be incorrect or the
server may be unreachable.

Invalid Windows NT
credentials

Check the username and password and try again.

Failed to retrieve user
information

Check that the entered username has a corresponding
name listed in the destinations list.

A value specified for XML
Meta Data <attribute>
ignored: the value has illegal
format

Check that the XML values correspond with the spec-
ified pattern.

MetaData Enabled. XML DD
file required

The AXIS 7100 failed to retrieve the XML DD file from
the FTP server. Contact the administrator.

XML Meta Data <attribute>
discarded: pattern is invalid

The pattern for the attribute in the XML DD file is in-
correct.

Message

Description

Summary of Contents for 7100






















































































































































































Search results

Summary of Contents for 7100

Reviews:

Axis 7100, User Manual, Page: 144 / 181

Search results

Summary of Contents for 7100

Reviews: