manualshive.com logo in svg

Axis 7100, User Manual, Page: 143 / 181

Share
Download
Axis 7100 User Manual Download Page 143

 

AXIS 7100

 

User’s Manual

Troubleshooting

143

Error and Warning Messages

This table lists the error and warning messages that might 

appear on the AXIS 7100 message display:

Message

Description

Out of memory

The document image contains too much data. Please 
try another profile.

Out of scanner image 
memory

The document image contains too much data. Please 
contact your equipment supplier.

Unresolved name:
<server name>

Cannot find the IP address mapped to <server name>.

Not available:
<server address>

Cannot establish communication with the server spec-
ified in <server address>. Please try again later.

Login failed:
<server address>

Incorrect FTP server password specified for the file 
destination.

Disconnected:
<destination>

The connection to the destination specified in <desti-
nation> has been lost. The image transfer has been 
aborted.

No valid mail recipient 
found

All the selected e-mail destinations were incorrect.

Illegal address 
<recipient>

Incorrect e-mail address specified for the e-mail des-
tination.

Illegal directory on:
<server address>

The directory specified for the file destination does not 
exist.

Unable to open file on:

Default file name is missing.

Write error on:
<server address>

Insufficient access rights to the directory specified for 
the file destination.

No info file on:
<server address>

The information file could not be stored on the FTP 
server. Possible reasons are lack of memory or naming 
conflicts. The image file will be removed.

Paper jam

Paper jam in the scanning device. Remove paper to 
continue sending.

No paper in scanner

No paper in the sheet feeder. 

Scanner not ready, please 
check scanner and retry

The scanning device is busy. Please try again. 

Could not connect to LDAP 
server

The DNS name or the IP address may be wrong. The 
server may be unreachable.

The user specified for LDAP 
is invalid

Invalid user name for the LDAP server. Enter a correct 
user name.

Invalid LDAP credentials 
(e.g. invalid user or 
password)

The LDAP server did not recognize the user with the 
specified password.

Summary of Contents for 7100






















































































































































































Reviews:

No comments