Agilent Technologies 2000 X-Series User Manual Download Page 332

Page: 332 / 352

332

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

I2C/SPI Triggering and Serial Decode

Interpreting SPI Lister Data

In addition to the standard Time column, the SPI Lister contains these
columns:

•

Data — data bytes (MOSI and MISO).

Aliased data is highlighted in pink. When this happens, decrease the
horizontal time/div setting and run again.

Searching for SPI Data in the Lister

The oscilloscope's search capability lets you search for (and mark) certain
types of SPI data in the Lister. You can use the

[Navigate]

key and controls

to navigate through the marked rows.

With SPI selected as the serial decode mode, press

[Search]

In the Search Menu, press the

Search

softkey; then, turn the Entry knob

to select the serial slot (Serial 1 or Serial 2) on which the SPI signals
are being decoded.

Press

Search

; then, select from these options:

•

Master-Out, Slave-In (MOSI) Data

— for searching MOSI data.

•

Master-In, Slave-Out (MISO) Data

— for searching MISO data.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands

Agilent Technologies 2000 X-Series, User Manual

Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands