manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 151

Trigger Mode/Coupling

11

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

151

 

The external trigger input impedance is 1M Ohm. This lets you use passive 
probes for general- purpose measurements. The higher impedance 
minimizes the loading effect of the oscilloscope on the device under test.

To set the EXT TRIG IN units and probe attenuation:

1

Press the 

[Mode/Coupling]

 key in the Trigger section of the front panel.

2

In the Trigger Mode and Coupling Menu, press the 

External

 softkey.

3

In the External Trigger Menu, press the 

Units

 softkey to select between:

•

Volts

 — for a voltage probe.

•

Amps

 — for a current probe.

Measurement results, channel sensitivity, and the trigger level will 
reflect the measurement units you have selected.

4

Press the 

Probe

 softkey; then, turn the entry knob to specify the probe 

attenuation.

The attenuation factor can be set from 0.1:1 to 1000:1 in a 1- 2- 5 
sequence.

The probe attenuation factor must be set properly for measurements to 
be made correctly.

C A U T I O N

 Maximum voltage at oscilloscope external trigger input

CAT I 300 Vrms, 400 Vpk; transient overvoltage 1.6 kVpk

1 M ohm input: For steady-state sinusoidal waveforms derate at 20 dB/decade above 
57 kHz to a minimum of 5 Vpk

With N2863A 10:1 probe: CAT I 600 V (DC + peak AC)

With 10073C or 10074C 10:1 probe: CAT I 500 Vpk

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands