Agilent Technologies 2000 X-Series User Manual Download Page 245

Page: 245 / 352

245

Agilent InfiniiVision 2000 X-Series Oscilloscopes
User's Guide

20
Utility Settings

I/O Interface Settings

245

Setting up the Oscilloscope's LAN Connection

246

File Explorer

249

Setting Oscilloscope Preferences

251

Setting the Oscilloscope's Clock

254

Setting the Rear Panel TRIG OUT Source

254

Performing Service Tasks

255

Configuring the [Quick Action] Key

261

Adding an Annotation

262

This chapter explains oscilloscope utility functions.

I/O Interface Settings

The oscilloscope can be accessed and/or controlled remotely via these I/O
interfaces:

•

USB device port on the rear panel (square shaped USB port).

•

LAN interface when a LAN/VGA module is installed in the rear panel
module slot.

•

GPIB interface when a GPIB module is installed in the rear panel
module slot.

To configure the I/O interfaces:

On the oscilloscope's front panel, press

[Utility]

In the Utility Menu, press

I/O

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands

Agilent Technologies 2000 X-Series, User Manual

Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands