manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 218

218

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

17

Waveform Generator

 

Notice that you can select between coarse and fine adjustments for 
frequency, period, and width. Also, pushing the Entry knob is a quick 
way to toggle between coarse and fine adjustments.

The 

Settings

 softkey opens the Waveform Generator Settings Menu which 

lets you make other settings related to the waveform generator.

See:

•

"To output the waveform generator sync pulse"

on page 218

•

"To specify the expected output load"

on page 219

•

"To use waveform generator logic presets"

on page 219

•

"To restore waveform generator defaults"

on page 225

To output the waveform generator sync pulse

1

If the Waveform Generator Menu is not currently displayed on the 
oscilloscope's softkeys, press the 

[Wave Gen]

 key.

2

In the Waveform Generator Menu, press the 

Settings

 softkey.

3

In the Waveform Generator Settings Menu, press the 

Trig Out

 softkey and 

turn the Entry knob to select 

Waveform Generator Sync Pulse

.

Waveform Type

Sync Signal Characteristics

All waveforms except 
DC and Noise

The Sync signal is a TTL positive pulse that occurs when the waveform 
rises above zero volts (or the DC offset value).

DC

N/A

Noise

N/A

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands