manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 167

Acquisition Control

12

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

167

 

See Also

•

"Navigating Segments"

on page 167

•

"Infinite Persistence with Segmented Memory"

on page 167

•

"Segmented Memory Re- Arm Time"

on page 168

•

"Saving Data from Segmented Memory"

on page 168

Navigating Segments

1

Press the 

Current Seg

 softkey and turn the Entry knob to display the 

desired segment along with a time tag indicating the time from the first 
trigger event.

You can also navigate segments using the 

[Navigate]

 key and controls. See 

"To navigate segments"

on page 57.

Infinite Persistence with Segmented Memory

When data has been acquired to segmented memory, you can also turn on 
infinite persistence (in the Display Menu) and press the 

Analyze Segments

 

softkey to create an infinite persistence display. The 

Analyze Segments

 

softkey appears when the acquisition is stopped and the segmented 
memory feature is on.

Progress indicator

Sample rate

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands