manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 304

304

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

23

CAN/LIN Triggering and Serial Decode

 

Interpreting CAN Decode

•

Frame ID appears in hex digits in yellow. Frames of 11 or 29 bits are 
automatically detected.

•

Remote frame (RMT) appears in green.

•

Data length code (DLC) appears in blue for data frames and green for 
remote frames.

•

Data bytes appear in hex digits in white for data frames.

•

Cyclic redundancy check (CRC) appears in hex digits in blue when 
valid, or in red to indicate that the oscilloscope's hardware decode 
calculated a CRC that is different from the incoming CRC data stream.

•

Angled waveforms show an active bus (inside a packet/frame).

•

Mid- level blue lines show an idle bus.

•

Decoded text is truncated at the end of the associated frame when 
there is insufficient space within frame boundaries.

•

Pink vertical bars indicate you need to expand the horizontal scale (and 
run again) to see decode.

•

Red dots in the decode line indicate that there is data that is not being 
displayed. Scroll or expand the horizontal scale to view the information.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands