manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 231

Save/Recall (Setups, Screens, Data)

18

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

231

 

•

Setup Info

 — when enabled, setup information (vertical, horizontal, 

trigger, acquisition, math, and display settings) is also saved in a 
separate file with a TXT extension.

•

Length

 — sets the number of data points that will be output to the 

file. For more information, see 

"Length Control"

on page 231.

•

Save Seg

 — when data is acquired to segmented memory, you can 

specify whether the currently displayed segment is saved or all 
acquired segments are saved. (See also 

"Saving Data from Segmented 

Memory"

on page 168.)

4

Finally, press the 

Press to Save

 softkey.

A message indicating whether the save was successful is displayed.

See Also

•

"Binary Data (.bin) Format"

on page 289

•

"CSV and ASCII XY files"

on page 296

•

"Minimum and Maximum Values in CSV Files"

on page 297

Length Control

The 

Length

  control  is  available  when  saving  data  to  CSV,  ASCII  XY,  or  BIN 

format  files.  It  sets  the  number  of  data  points  that  will  be  output  to  the 
file. Only displayed data points are saved.

The maximum number of data points depends on these things:

•

Whether acquisitions are running. When stopped, data comes from the 
raw acquisition record. When running, data comes from the smaller 
measurement record.

•

Whether the oscilloscope was stopped using 

[Stop]

 or 

[Single]

. Running 

acquisitions split memory to provide fast waveform update rates. Single 
acquisitions use full memory.

•

Whether only one channel of a pair is turned on. (Channels 1 and 2 are 
one pair, channels 3 and 4 are the other.) Acquisition memory is 
divided among the channels in a pair.

•

Whether reference waveforms are on. Displayed reference waveforms 
consume acquisition memory.

•

Whether digital channels are on. Displayed digital channels consume 
acquisition memory.

•

Whether segmented memory is on. Acquisition memory is divided by 
the number of segments.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands