manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 308

308

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

23

CAN/LIN Triggering and Serial Decode

 

2

Press 

[Serial]

.

3

Press the 

Mode

 softkey; then, select 

LIN

 trigger type.

4

Press the 

Signals

 softkey to open the LIN Signals Menu.

5

Press the 

Source

 softkey to select the channel connected to the LIN 

signal line.

The label for the LIN source channel is automatically set.

6

Press the 

Threshold

 softkey; then, turn the Entry knob to set the LIN 

signal threshold voltage level to the middle of the LIN signal.

The threshold voltage level is used in decoding, and it will become the 
trigger level when the trigger type is set to the selected serial decode 
slot.

7

Press the 

Baud Rate

 softkey to open the LIN Baud Rate Menu.

8

Press the 

Baud

 softkey; then, turn the Entry knob to select the baud 

rate that matches match your LIN bus signal.

The default baud rate is 19.2 kb/s.

If none of the pre- defined selections match your LIN bus signal, select 

User Defined

; then, press the 

User Baud

 softkey and turn the Entry knob 

to enter the baud rate.

You can set the LIN baud rate from 2.4 kb/s to 625 kb/s in increments 
of 100 b/s.

9

Press the 

Back/Up key to return to the LIN Signals Menu.

10

Press the 

Sample Point

 softkey; then, turn the Entry knob to select the 

sample point at which the oscilloscope will sample the bit value.

Back

60%

70%

80%

Sample Point

One Bit

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands