manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 246

246

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

20

Utility Settings

 

3

In the I/O Menu, press 

Configure

.

•

LAN

 — When a DSOXLAN LAN/VGA module is installed, you can use 

the 

LAN Settings

 and 

LAN Reset

 softkeys to configure the LAN 

interface. See 

"Setting up the Oscilloscope's LAN Connection"

on 

page 246.

•

GPIB

  —  When  a  DSOXGPIB  GPIB  module  is  installed,  you  can  use  the 

Address

 softkey to configure the GPIB address.

•

There are no configuration settings for the USB interface.

When an I/O interface is installed, remote control over that interface is 
always enabled. Also, the oscilloscope can be controlled via multiple I/O 
interfaces (for example, USB and LAN) at the same time.

See Also

•

Chapter 21

, “Web Interface,” starting on page 265 (when the 

oscilloscope is connected to a LAN).

•

"Remote Programming via the Web Interface"

on page 271

•

The oscilloscope's 

Programmer's Guide

.

•

"Remote Programming with Agilent IO Libraries"

on page 272

Setting up the Oscilloscope's LAN Connection

When the DSOXLAN LAN/VGA module is installed, you can place the 
oscilloscope on the network and set up its LAN connection. Once that is 
done, you can use the oscilloscope's web interface or remotely control the 
oscilloscope via the LAN interface.

The oscilloscope supports methods for automated LAN configuration or 
manual LAN configuration (see 

"To establish a LAN connection"

on 

page 247). It is also possible to set up a point- to- point LAN connection 
between a PC and the oscilloscope (see 

"Stand- alone (Point- to- Point) 

Connection to a PC"

on page 248).

Once the oscilloscope is set up on the network, you can use the 
oscilloscope's web page to view or change its network configuration and 
access additional settings (like the network password). See 

Chapter 21

, 

“Web Interface,” starting on page 265.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands