Agilent Technologies 2000 X-Series User Manual Download Page 243

Page: 243 / 352

Print (Screens)

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

243

To specify the palette option

In the Print Configuration Menu, press the

Palette

softkey to change the

following options.

•

Color

— Select this to print the screen in color.

The oscilloscope's print driver cannot print color images to color laser
printers, so the

Color

option is not available when connected to laser

printers.

•

Grayscale

— Select this to print the screen in shades of gray rather than

in color.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands

Agilent Technologies 2000 X-Series, User Manual

Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands