Agilent Technologies 2000 X-Series User Manual Download Page 9

Page: 9 / 352

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

To specify the channel units

To specify the probe attenuation

To specify the probe skew

Math Waveforms

To display math waveforms

To perform a transform function on an arithmetic operation

To adjust the math waveform scale and offset

Units for Math Waveforms

Math Operators

Add or Subtract

Multiply or Divide

Math Transforms

FFT Measurement

Reference Waveforms

To save a waveform to a reference waveform location

To display a reference waveform

To scale and position reference waveforms

To adjust reference waveform skew

To display reference waveform information

To save/recall reference waveform files to/from a USB storage

device

Digital Channels

To connect the digital probes to the device under test

Probe cable for digital channels

Acquiring waveforms using the digital channels

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands

Agilent Technologies 2000 X-Series, User Manual

Search results

Summary of Contents for 2000 X-Series

Reviews:

Related manuals for 2000 X-Series

Brands by name

Popular brands