manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 249

Utility Settings

20

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

249

 

This may take a few minutes.

Now, the instrument is connected, and the instrument's web interface or 
remote control via LAN may be used.

File Explorer

The File Explorer lets you navigate the oscilloscope's internal file system 
and the file systems of connected USB storage devices.

From the internal file system, you can load oscilloscope setup files or 
mask files.

From a connected USB storage device, you can load setup files, mask files, 
license files, firmware update (*.cab) files, label files, etc. Also, you can 
delete files on a connected USB storage device.

The oscilloscope's internal file system, under "\Agilent Flash", consists of 
10 locations for oscilloscope setup files, and four locations for mask files.

To use the File Explorer:

1

Press 

[Utility] > File Explorer

.

2

In the File Explorer Menu, press the softkey in the first position and 
use the Entry knob to navigate.

N O T E

The USB port on the front panel, and the USB port on the rear panel labeled "HOST" are 
USB Series A receptacles. These are the receptacles to which you can connect USB mass 
storage devices and printers.

The square receptacle on the rear panel labeled "DEVICE" is provided for controlling the 
oscilloscope over USB. See the Programmer's Guide for more information.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands