manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 131

Triggers

10

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

131

 

Pulse Width Trigger

Pulse Width (glitch) triggering sets the oscilloscope to trigger on a positive 
or negative pulse of a specified width. If you want to trigger on a specific 
timeout value, use 

Pattern

 trigger in the Trigger Menu (see 

"Pattern 

Trigger"

on page 128).

1

Press the 

[Trigger]

 key.

2

In the Trigger Menu, press the 

Trigger

 softkey; then, turn the Entry knob 

to select 

Pulse Width

.

3

Press the 

Source

 softkey; then, rotate the Entry knob to select a channel 

source for the trigger.

The channel you select is shown in the upper- right corner of the 
display next to the polarity symbol.

The source can be any analog or digital channel available on your 
oscilloscope.

4

Adjust the trigger level:

•

For analog channels, turn the Trigger Level knob.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands