manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 199

199

Agilent InfiniiVision 2000 X-Series Oscilloscopes 
User's Guide

 

s

1

15
Mask Testing

To create a mask from a "golden" waveform (Automask)

199

Mask Test Setup Options

201

Mask Statistics

204

To manually modify a mask file

205

Building a Mask File

208

One way to verify a waveform's compliance to a particular set of 
parameters is to use mask testing. A mask defines a region of the 
oscilloscope's display in which the waveform must remain in order to 
comply with chosen parameters. Compliance to the mask is verified 
point- by- point across the display. Mask test operates on displayed analog 
channels; it does not operate on channels that are not displayed.

To  enable  mask  test  order  Option  LMT  at time of oscilloscope purchase, or 
order DSOX2MASK as a stand- alone item after oscilloscope purchase.

To create a mask from a "golden" waveform (Automask)

A golden waveform meets all chosen parameters, and it is the waveform to 
which all others will be compared.

1

Configure the oscilloscope to display the golden waveform.

2

Press the 

[Analyze]

 key.

3

Press 

Features

; then, select 

Mask Test

.

4

Press 

Features

 again to enable mask testing.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands