manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 149

Trigger Mode/Coupling

11

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

149

 

Note that Trigger Coupling is independent of Channel Coupling (see 

"To 

specify channel coupling"

on page 61).

To enable or disable trigger noise rejection

Noise Rej adds additional hysteresis to the trigger circuitry. By increasing 
the trigger hysteresis band, you reduce the possibility of triggering on 
noise. However, this also decreases the trigger sensitivity so that a slightly 
larger signal is required to trigger the oscilloscope.

1

Press the 

[Mode/Coupling]

 key.

2

In the Trigger Mode and Coupling Menu, press the 

Noise Rej

 softkey to 

enable or disable.

To enable or disable trigger HF Reject

HF Reject adds a 50 kHz low- pass filter in the trigger path to remove high 
frequency components from the trigger waveform.

You can use HF Reject to remove high- frequency noise, such as AM or FM 
broadcast stations or noise from fast system clocks, from the trigger path.

1

Press the 

[Mode/Coupling]

 key.

2

In the Trigger Mode and Coupling Menu, press the 

HF Reject

 softkey to 

enable or disable.

Pass
Band

50 kHz

DC

0 dB

-3 dB

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands