manualshive.com logo in svg

Agilent Technologies 2000 X-Series, User Manual

Share
Download
Agilent Technologies 2000 X-Series User Manual Download Page 262

262

Agilent InfiniiVision 2000 X-Series Oscilloscopes User's Guide

20

Utility Settings

 

Adding an Annotation

You can add an annotation to the upper left corner of the oscilloscope's 
display. The annotation is useful for documentation purposes, to add notes 
before capturing screens.

To add an annotation:

1

On the oscilloscope's front panel, press 

[Utility]

.

2

In the Utility Menu, press 

Annotation

.

3

In the Annotation Menu, press 

Annotation

 to enable the annotation.

4

Press 

Edit

.

5

In the Edit Annotation Menu:

•

Use the 

Spell

, , , 

and 

Delete Character

 softkeys to enter the 

annotation text:

•

Spell

 — press this softkey and turn the Entry knob to select the 

character at the current position.

•

 — press this softkey to enter characters and move the cursor 

to the next character position.

Summary of Contents for 2000 X-Series

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands